0 Item(s) in Cart
£0.00
You have no items in your shopping cart.
Details
With our MFD15 we bring the Can Bus into the 52mm display
THE MFD15 - KEY FEATURES
Best legibility thanks to OLED technology
freely programmable control units and OBD2 connection
FOUR analog inputs for additional sensors (oil temperature, oil pressure, fuel pressure)
freely definable warning thresholds per sensor
integrated shift light LED - freely configurable
Sensors
- min: lowest value that has occurred
- min warn: Value from which a warning is issued if the value is undershot
- max: highest value that has occurred
- max warn value: value from which a warning is given if it is exceeded
- Beep: a tone is emitted when the "min/max warning value" is exceeded or not reached
- Popup: If the value falls below or exceeds the "min/max warning value", a popup window is displayed
- RefSensor: only when this sensor...
- RefValue: ... above this value will be warned
The values of analog sensors (0-5V) can be displayed correctly using 2-point calibration. For example, the correct oil pressure is displayed and not a voltage. You can also assign names to the analogue sensors - instead of AN1, "Oil pressure" really does appear in the display. In addition, the inputs can be activated individually via the "Active" option if you need them.
Shift light
- 8 values - each individually adjustable
- speed limits
- Colours
- Flash speed - the entire shift light flashes
- Shift light brightness
Warnings
In the displays themselves, values that have been exceeded are shown in red and values that have not been reached are shown in blue.
If a sensor is undercut/exceeded that is not currently displayed, the sensor setting determines what happens: popup, warning buzzer or just a small yellow triangle in the top right corner of the status bar.
Representation of exceeded and undershot values
Exceeding or falling below a sensor can be displayed in various ways:
1) Sensor is not in the current display: as soon as a sensor exceeds the set min or max warning value, an arrow appears at the top right (arrow up: max value exceeded, arrow down: min value exceeded)
2) Sensor is currently exceeding a value in the current display: Max exceeded (the number is red), Below Min (the number is blue)
3) Sensor is shown and has exceeded a threshold value in the past: a triangle appears next to the sensor (arrow up: max value exceeded, arrow down: min value exceeded)
4) If a sensor has been exceeded or fallen short of, you can see exactly which one in the sensor settings
The following control units are currently supported:
- trijekt (Premium, Bee, trigifant) - trijekt plus with restrictions
- Megasquirt 2 and 3
- K-Data KDFI
- UMC1/UMC2
- Ecumaster EMU Black and Classic (with Can Bus Adapter)
- van Kronenburg KMS MD35 and MP25 (with Can Bus Adapter) - VAG (VW/Audi/Seat)
- Motorsport Electronics ME221/ME442 (Can Bus)
- LinkECU
- MaxxECU
- Motec
- SCS Delta
- BMW E46 Can Bus Protocol
- VW/Audi Can Bus Protocol
– OBD2 Can Bus (250/500kbit 11/29bit)
With serial adapter:
- VEMS
- ME221
The MFD15 is delivered with:
- Display (MFD15)
- Rotary knob with 0.5m connection cable
- Adapter cable for connecting 12V and updating the display
- MicroUSB data cable for updates
- Connection plugs for analog inputs and Can Bus
- 20cm pre-crimped connection cable for Can Bus, analog inputs, 5V and sensor ground
- Pins to crimp yourself
We have developed our own firmware for the MFD15, which queries data directly via OBD2 Can Bus. You have to set the speed (250kbit or 500kbit) yourself. Furthermore, the display automatically recognizes 11bit and 29bit identifiers.
With our OBD Plug and Play cable, the connection is made directly to the OBD socket. In addition, only the 12V supply has to be tapped with the enclosed fuse adapter.
The following values are read out:*
With our OBD Plug and Play cable, the connection is made directly to the OBD socket. In addition, only the 12V supply has to be tapped with the enclosed fuse adapter.
The following values are read out:*
- Speed (RPM)
- engine load
- Fuel pressure (FuelPressure)
- Boost pressure (MAP)
- Vehicle speed (Speed)
- Ignition angle (IgnAng)
- Intake temperature (IAT)
- Air Mass (MAF)
- Oil temperature (OilTemp)
- Fuel pressure relative to intake vacuum (FuelRail)
- water temperature (CLT)
- Lambda1-8
- Cat Temperature Bank1 Sensor 1 (CatTemp1)
- Cat Temperature Bank1 Sensor 2 (CatTemp2)
- Cat Temperature Bank2 Sensor 1 (CatTemp3)
- Cat Temperature Bank2 Sensor 2 (CatTemp4)
- Additionally 4 analogue inputs
More Info
| Manufacturer | CANchecked |
|---|---|
| Fitment | No |
| Colour | N/A |
| Note | No |
- Be the first to review this product
You may also be interested in
CANchecked MFA 2.0 Multi Function Display Mazda MX-5 NB/NBFL
£198.93 Excl. Tax £238.72 Incl. Tax
CANchecked MFD15 Multi Function Display Mazda MX5 NC
£228.42 Excl. Tax £274.10 Incl. Tax
CANchecked MFD15 Multi Function Display Mazda MX5 ND
£228.42 Excl. Tax £274.10 Incl. Tax
© Tegiwa Imports Ltd | Registered in England Number 5798174
Finance provided by PayPal Credit. Terms and conditions apply. Credit subject to status, UK residents only, Tegiwa Imports LTD acts as a broker and offers finance from a restricted range of finance providers. PayPal Credit is a trading name of PayPal UK Ltd, Whittaker House, Whittaker Avenue, Richmond-Upon-Thames, Surrey, United Kingdom, TW9 1EH.
Finance provided by PayPal Credit. Terms and conditions apply. Credit subject to status, UK residents only, Tegiwa Imports LTD acts as a broker and offers finance from a restricted range of finance providers. PayPal Credit is a trading name of PayPal UK Ltd, Whittaker House, Whittaker Avenue, Richmond-Upon-Thames, Surrey, United Kingdom, TW9 1EH.